UC San Diego’s Soft Robot Runs 100x Faster Without Electronics

UC San Diego engineers reported Wednesday a soft, six-legged robot runs 100 times faster, reaching 4.72 meters per second, without any electronic components.

A six-legged robot made entirely of soft material now scoots along at 4.72 meters per second — more than 5 yards every second — without a single electronic component inside it, engineers at the University of California San Diego reported Wednesday.

That speed, achieved with nothing but pressurized air, makes it the fastest soft robot ever built.

The machine, designed and tested at UC San Diego’s Jacobs School of Engineering, runs on concrete, gravel, lawn, mulch and sand. It can run down stairs, swim, and keep walking underwater. And it comes off a 3D printer in one piece, made of one material, as the university’s news office reported this week.

Why it matters: soft robots are exactly the kind of machines you’d want in places electronics cannot survive — reactors laced with radiation, disaster zones, magnetic fields, the surface of another planet. Until now, they’ve been too slow to be useful in any of them. This one changes that math.

Coming soon to a beach near you: a soft robot that can move at over 5 yards per second

“Our first walking robot demonstrated what was possible, but it was too slow. We hoped to overcome this limitation, and we were fortunate to find a solution to make the new robot 100 times faster,” said Yichen Zhai, a former postdoctoral researcher in the lab of Professor Michael T. Tolley at UC San Diego.

A steam engine trick, printed in rubber

The leap in speed came from an idea older than the automobile. The 19th-century compound steam engine let steam expand through multiple chambers to squeeze out every last bit of energy. The UC San Diego team, per Nanowerk’s report, borrowed that logic for a robot with no metal, no fire and no circuits.

The robot’s interior is a connected series of chambers, valves and tubes. Pressurized air circulates through it twice — first through smaller, high-pressure chambers that power the valves, then through larger, low-pressure chambers that drive the legs. That two-stage design stops the robot from wastefully venting air that still carries energy, which is what capped its predecessor.

That earlier machine, built by the same team in 2022 and described in Advanced Intelligent Systems in 2025, managed just 4 centimeters per second — roughly 1.5 inches, slower than a snail’s stroll. Its limit was the air pressure and airflow its soft body could tolerate. The new robot, detailed in the journal Science Robotics, is bigger and stronger inside to handle higher pressures, and the compound-chamber trick makes that pressure count.

YouTube video title: Watch the robot in action

The result is a speed gain of more than 100 times over the 2022 version. For scale: the new robot covers in one second what the old one needed more than a minute and a half to travel.

Robot needs compressed-air tether

The team put the robot through its paces on an unusually long list of surfaces: concrete, gravel, lawn, mulch, sand. It handled stairs and water. According to Nanowerk’s coverage, it could swim at the surface and keep functioning while submerged.

There’s one honest catch, and the researchers name it themselves. The robot still needs a tether to a source of compressed air — a traditional air compressor, for now. That leash keeps it out of the field and in the lab.

The team’s roadmap, as UC San Diego reported, runs in two directions: designs that sip less compressed air so the robot can run untethered off something as portable as a cartridge, and more complex motion — steering, object manipulation. Zhai framed the ambition plainly.

“The key challenge was to implement a time-tested solution (the compound steam engine) in a soft running robot that can be printed in a single piece out of a single material,” Zhai said. “We see this as a step towards complex and powerful robots that can be printed on the desktop using inexpensive materials.”

The market for machines with no brain

Here’s the angle that’s easy to miss: an electronics-free robot isn’t a limitation dressed up as a feature. It’s a ticket to environments where silicon dies. High radiation scrambles circuits. Strong magnetic fields wreck them. Disaster sites — the collapsed building, the flooded subway — punish anything fragile and battery-dependent.

A soft robot printed on a desktop for the cost of a spool of material, powered by air, could walk into those places where a conventional robot wouldn’t last an hour. The researchers point to scientific reconnaissance in radiation zones, disaster response and space exploration as the long-term applications. The work was funded by the National Science Foundation.

It’s also worth watching the manufacturing story. Because the robot prints in a single piece from a single material, there’s no assembly, no wiring, no supply chain of motors and chips. Desktop fabrication of capable machines — not just prototypes, but working robots — is the quiet economic shift underneath this headline.

The tether is the open question, and the researchers are the first to say the untethered version doesn’t exist yet. But the trajectory is hard to argue with: 4 centimeters per second in 2022, 4.72 meters per second now, and a design philosophy borrowed from engines that powered ships a century and a half ago.

Tolley, a professor of mechanical and aerospace engineering at UC San Diego’s Jacobs School of Engineering, has spent his career on machines that borrow from nature. Before joining the faculty, he was a postdoctoral fellow at Harvard University’s Wyss Institute for Biologically Inspired Engineering from 2011 to 2014, and he earned his Ph.D. at Cornell University’s Creative Machines Lab.

In work published in the journal Science, he and his co-authors showed a robot printed as a flat sheet with embedded electronics that folded itself into a functional machine and began operating on its own. He has also built untethered soft robots inspired by cephalopods that can walk and jump without rigid parts.

The science, as the team put it in the title of their Science Robotics paper, is about printing powerful soft robotics on a desktop. The next milestone — a robot that carries its own air — is the one that gets it out the door.

Photo of author

Newsroom

Newsroom at Archyde.

Beihang, CityU Electronic Comb Regrows 97.85% of Hair on Mice in 28 Days

Nike Unveils ‘Full Stride Ahead’ Turnaround Plan Targeting $5 Billion Growth by 2031