Nikon is known for cameras, but for more than four decades it has built the machines that print the circuits inside the world’s chips.
Japan’s Nippon Kogaku, founded in 1917, quietly shipped its first semiconductor stepper in 1980, and its lithography systems still shape how modern silicon gets made.
The gap between the two businesses is wider than most consumers realize. A DSLR buyer sees the Nikon badge on a camera body. A chipmaker sees the same company’s optics projecting circuit patterns onto wafers at resolutions measured in nanometers — vietnam.vn reported, drawing on Báo Khoa học và Đời sống.
That second business began in 1976, when Nikon started lithography research at the suggestion of Japan’s VLSI research association, the group formed to push large-scale integrated circuits. Four years later the company announced the NSR-1010G, the first stepper made in Japan, with a resolution of 1 micrometer — 1,000 nanometers.
By 1984, Nikon had moved further. That year it introduced the NSR-1010i2, which vietnam.vn describes as the world’s first stepper to use an i-line light source. The camera lens expertise — light handling, precision optics, fine mechanics — had found a second, industrial life.
How a stepper actually works
The principle is straightforward, even if the execution is not. A silicon wafer gets coated with a light-sensitive material called photoresist. The machine aligns the wafer with a photomask, then uses a light source and a lens system to shrink the mask’s circuit pattern and project it onto the wafer surface.
Wherever the light hits, the resist changes its properties, which makes the later etching and processing steps possible. The process repeats layer after layer, building up the complex stack of interconnects and transistors that make up a finished chip.
One sentence, then, sums up the whole machine: it is a camera that photographs circuits onto silicon instead of pictures onto film.
Nikon advances from dry to immersion ArF lithography
The most consequential technique in Nikon’s current lineup is ArF immersion lithography. It relies on an argon fluoride excimer laser with a wavelength of 193 nanometers, and it adds a layer of pure water between the lens and the wafer. Because of water’s refractive properties, the system resolves finer detail than lithography done in air.
Nikon’s timeline here matters. In 1999 it shipped the NSR-S302A, a dry ArF lithography machine. By 2006 it had moved to the NSR-S609B, a mass-production immersion system with a numerical aperture of 1.07 — a figure that marks the jump from air to water as the imaging medium.
The current flagship cited in the reporting is the NSR-S636E, one of Nikon’s ArF immersion systems for advanced integrated circuit fabrication. Per the manufacturer’s own specifications, it uses the same 193-nanometer ArF light source, achieves a maximum resolution of 38 nanometers, holds overlay accuracy to no more than 2.1 nanometers, and processes at least 280 wafers per hour under the company’s own measurement conditions, according to Vietnam.
Those three numbers tell a story on their own. Compare the 1980 machine’s 1,000-nanometer resolution with the 38 nanometers of today’s immersion systems, and the improvement spans more than a factor of 25 in the same basic imaging problem.
Why 38 nanometers still matters
A resolution of 38 nanometers sounds coarse next to the leading-edge nodes discussed in the industry. The reason it still counts is a technique called multiple patterning: instead of printing a structure in one exposure, the work is split across several processing steps, each forming features smaller than a single exposure could deliver.
Vietnam.vn’s report states that immersion lithography combined with these multi-patterning techniques makes it possible to produce chips at process sizes below 10 nanometers. That is the bridge between Nikon’s optical systems and the most advanced logic fabrication — no shorter wavelengths required, just more passes.
This is also where Nikon’s position in the market becomes clear. The company does not sell the extreme ultraviolet tools that dominate headlines about leading-edge fabs. Its ArF immersion and multi-patterning route competes on a different axis: proven optical engineering applied repeatedly, layer by layer.
The wider Nikon that consumers never see
Nikon’s reach beyond cameras extends to microscopes, measuring instruments, lithography and semiconductors, according to the report. None of those products reach consumers directly. All of them, though, sit underneath the devices that do — the smartphones, PCs and electronics built on silicon patterned by machines like the NSR line.
The contrast with the camera business is the point. One side faces consumers and reviewers; the other faces a handful of chipmakers, and its output is measured in overlay accuracy and wafers per hour rather than megapixels.
What remains unresolved is market share. The sourced material documents Nikon’s technical lineage and current specifications in detail, but it does not state how many of the world’s steppers the company sells today, or how its shipments compare with rivals’. That number — the one that would settle whether Nikon’s second act is growing or holding steady — is not in the record here.
Nikon’s roots go deeper than cameras. The company was formed on July 25, 1917, when three leading Japanese optical manufacturers merged into a fully integrated optical company, and in its early decades it made the lenses for the first Canon cameras.
Its optics found a global audience after the American photojournalist David Douglas Duncan fitted Nikon lenses to his Leica cameras while covering the Korean War from 1950 to 1951. The company kept the name Nippon Kogaku until 1988, when it took the name Nikon Corporation from its cameras, and it remains part of the Mitsubishi group of companies.
What the record does establish is this: a company founded in 1917 as Nippon Kogaku took the optics it built for cameras and, starting in 1976, turned them into machines that print circuits at 38 nanometers, 280 wafers an hour.